Bai, Grace Please click on the pdf file for reading in the mobile phone.
| 检验项目 Inspection Item | 检验标准 Inspection Standard | 检验方法/依据 Method/Basis |
| 包装检验 Packaging Inspection | ||
| 外箱标识 Carton Labeling | 外箱标识清晰、完整 Carton label is clear and complete | 目测/样品 Visual/Sample |
| 包装正确性 Packaging Accuracy | 外箱标识正确，箱内产品与箱外标识一致，无漏装、错装、少装等不良现象 Correct carton labeling, product inside matches external label, no missing/wrong/insufficient packaging | 目测/样品 Visual/Sample |
| 颜色与表面 Color & Surface | 颜色无色差、丝印内容、材质须与样品一致，印字无重影、残缺、断线等 No color difference, silkscreen content and material match sample, no ghosting, defects or broken lines in printing | 目测 Visual |
| 外观检验 Appearance Inspection | ||
| 异色点 Discoloration Points | 正面：≤0.2mm两点距离大于50mm；LOGO 20mm内不允许有。侧面、底面：≤0.4mm两点距离大于30mm Front: ≤0.2mm points >50mm apart; none within 20mm of LOGO. Sides/Bottom: ≤0.4mm points >30mm apart | 目视/样品/卡尺/菲林片/塞规 Visual/Sample/Calipers/Film/Feeler Gauge |
| 刮伤Scratches | A面：不超过5mm*0.1mm的划痕、无刮手现象1条，30cm目视不明显；B面：不超过10mm*0.1mm的划痕、无刮手现象，不同面允许1条，30cm目视不明显 A-side: ≤1 scratch of 5mm*0.1mm, not sharp, invisible at 30cm. B-side: ≤1 scratch per side of 10mm*0.1mm, not sharp, invisible at 30cm | 目视 Visual |
| 间隙 Gap | 间隙≤0.2mm Gap ≤0.2mm | 目视/塞规 Visual/Feeler Gauge |
| 断差 Step Difference | 底壳大于面壳：断差≤0.2mm；底壳小于面壳：断差≤0.4mm Bottom > Top: ≤0.2mm; Bottom < Top: ≤0.4mm | 目视/塞规 Visual/Feeler Gauge |
| 批锋 Burrs | 不可有刮手现象，不可影响装配和外观 No sharp edges, must not affect assembly or appearance | 目视/手感 Visual/Touch |
| 变形 Deformation | 键盘长度方向变形≤2mm，宽度方向变形≤1mm,不可以有晃动现象 Deformation ≤2mm lengthwise, ≤1mm widthwise, no wobbling | 玻璃台面/塞规测量 Glass Platform/Feeler Gauge |
| 硅胶垫 Silicone Pad | 不可歪斜、脏污和漏装，不可装错颜色和厚度，摩擦后硅胶垫不可脱落 No tilting, dirt or missing; correct color and thickness; must not detach after rubbing | 目视/手动 Visual/Manual |
| 色差 Color Difference | 表面油漆（橡胶漆）色差，20CM直观正常视觉能看出来 Paint (rubber paint) color difference visible at 20cm under normal vision | 目视 Visual |
| 密合度 Sealing | 用力掰动上下盖，松动不密合，间隙小于等于0.2mm When twisting top/bottom covers, gap ≤0.2mm if loose | 手动 Manual |
| 密合度 Sealing | 用力掰动上下盖，松动不密合，间隙大于0.2mm When twisting top/bottom covers, gap >0.2mm if loose | 手动 Manual |
| 漏打螺丝 Missing Screws | 不可有漏打螺钉 No missing screws | 目视 Visual |
| PIN Key Pin | 按键不可出现下陷，不回弹现象 Keys must not sink or fail to rebound | 手动按压 Manual Press |
| 卡键 Sticky Keys | 手动按压按键，按键不可有死键或卡键现象,按动按键边缘，功能正常 Keys must not be dead or sticky; function normal when pressing edges | 手动按压 Manual Press |
| 平整度 Flatness | 产品表面不平整，手感、肉眼明显看到，相邻键帽高度差小于0.4mm Surface unevenness visible/tangible; adjacent keycap height difference <0.4mm | 目视/手感 Visual/Touch |
| 错键 Wrong Key | 不可有错键 No wrong keys | 目视/功能测试 Visual/Functional Test |
| 掉键 Key Falling | 用拉力计拔动键帽，≤0.8KG拉力掉键 Key must not detach under ≤0.8KG pull force | 拉力计测试 Dynamometer Test |
| 键帽高低不平 Keycap Height | 键帽与键帽之间,整个面高低断差≤0.4MM，键帽倾斜≤20° Keycap height difference ≤0.4mm across surface; keycap tilt ≤20° | 目视/测量 Visual/Measurement |
| 轻按不显 Light Press Failure | 正常力度按压按键,按键功能失效 Key function fails under normal pressure | 手动按压 Manual Press |
| 灵敏度高 High Sensitivity | 轻触按键表面,≤20g按键不可有电性 No electrical response under ≤20g touch | 压力测试 Pressure Test |
| 连显 Multiple Display | 正常按压一次按键,按一次不可连续显示几个字符 Single press must not display multiple characters | 功能测试 Functional Test |
| 手感 Key Feel | 手动正常按压按键，按键手感无异常 Key feel normal under manual pressing | 手动按压 Manual Press |
| 唤醒 Wake Up | 锁屏后按任意键一次或滑动触摸板，可正常唤醒屏幕 Screen wakes normally after lock by pressing any key or sliding touchpad | 手动测试 Manual Test |
| 按键丝印 Key Silkscreen | 丝印内容、颜色与丝印图档或样板相符，字体或符号无漏印、错印、印刷缺损 Silkscreen content/color matches file/sample; no missing/wrong/defective printing | 目视/样品 Visual/Sample |
| LOGO Logo | 丝印内容、颜色与丝印图档或样板相符，字体或符号无印刷缺陷，尺寸位置无异常 Logo content/color matches file/sample; no printing defects; correct size/position | 目视/样品 Visual/Sample |
| 结构尺寸 Dimensions | ||
| 所有尺寸符合图纸要求或和样品一致,在检查时摇动产品，检查产品内是否有异响 All dimensions match drawing/sample; no abnormal sound when shaking | 卡尺/样品 Calipers/Sample | |
| 功能测试 Functional Test | ||
| 开机 Power On | 打开蓝牙键盘到”ON”位，电源开关手感无不良，亮灯正常，不可有不能开机现象 Switch to “ON”: switch feel normal, LED lights up, no failure to power on | 目视/手动 Visual/Manual |
| 蓝牙搜索与连接 Bluetooth Search & Pairing | 开机后按”Connect”键,蓝牙灯闪亮正常，蓝牙名正确，蓝牙可被平板正常搜索到，输入配对码后连接无异常 Press “Connect”: BT light flashes, correct name, discoverable, pairs normally after code input | 目视/手动 Visual/Manual |
| 回连检验 Reconnection | 1.关掉平板不关键盘，打开平板后键盘按任意键可回连；2.关掉键盘不关平板，打开键盘后可自动回连 1. Turn off tablet (keyboard on), keyboard reconnects on key press; 2. Turn off keyboard (tablet on), auto reconnects when on | 手动 Manual |
| 信号检验 Signal Test | 用连接好的键盘到离平板或电脑（中间无障碍）方圆10m内各位置进行测试，功能无异常 Test within 10m radius of device (no obstacles), no functional issues | 手动 Manual |
| LED灯 LED Light | 装入电池，打开开关，不可有灯不亮现象，颜色亮度与实际规定不相符 With batteries: all LEDs light, correct color/brightness | 手动 Manual |
| 拍打测试 Tap Test | 反过键盘，手拍键盘背面（适当力度）键帽不能有脱落现 Turn over and tap back (moderate force): keycaps must not detach | 手动 Manual |
| 干扰测试 Interference Test | 多个蓝牙（无线）键盘同时使用是否存在干扰 No interference when multiple BT/wireless keyboards used simultaneously | 手动 Manual |
| 休眠、唤醒测试 Sleep/Wake Test | 静止10分钟/30分钟/60分钟，再用键盘是否工作正常，唤醒时间小于3s After 10/30/60min inactivity, keyboard works normally; wake time <3s | 手动 Manual |
| 高温储存 High Temp Storage | 1.温度：60度 时间：8H 2.常温恢复2H 产品外观/性能/结构正常 60°C for 8H → 2H recovery at RT: appearance/function/structure normal | 恒温恒湿试验箱 Chamber |
| 低温储存 Low Temp Storage | 1.温度：-20度 时间：8H 2.常温恢复2H 产品外观/性能/结构正常 -20°C for 8H → 2H recovery at RT: appearance/function/structure normal | 恒温恒湿试验箱 Chamber |
| 恒温恒湿储存 Constant Temp/Humidity | 1.温度：40度 湿度：90%RH 时间：48H 2.常温恢复2H 产品外观/性能/结构正常 40°C/90%RH for 48H → 2H recovery at RT: appearance/function/structure normal | 恒温恒湿试验箱 Chamber |
| 拉拔力测试 Pull Force Test | 用拉力计把键帽从键盘上拉出来，垂直用力，不可倾斜用力，键帽拉力≧1.2KG Keycap pull force ≥1.2KG (vertical force only) | 拉力计 Dynamometer |
| 按键寿命测试 Key Life Test | 动作频率：2~4次/秒，动作力：200g+/-50g，测试次数：500万次，测试后，按键按压及回弹畅，按压按键能正常导通 2-4 presses/sec, 200g±50g, 5M cycles: keys press/rebound smoothly, function normal | 测试仪 Tester |
| 可靠性测试 Reliability Test | ||
| 裸机跌落实验 Naked Drop Test | 从76cm的高度自由跌落到专用地板，测试后不能有构件脱落，影响使用的断裂等不良现象 Free drop from 76cm to specified floor: no part detachment/breakage affecting use | 跌落台 Drop Tester |
| 酒精耐磨 Alcohol Rub | 耐磨头施加500g力，测试频率40-60来回/分钟，丝印+UV摩擦1000次 500g force, 40-60 cycles/min, 1000 cycles for silkscreen+UV | 耐磨试验机/橡皮擦 Rub Tester/Eraser |
| 百格试验 Cross-Cut Test | 用锋利刀片划10*10个1mm*1mm小网格，用3M600号胶纸粘住后迅速撕开，喷涂层无脱落现象 10×10 1mm grids cut, 3M tape applied/removed: no coating detachment | 百格刀/3M胶纸 Cross-Cutter/3M Tape |
| 兼容性试验 Compatibility Test | 使用现市面所有系统连接上键盘，键盘是否工作正常（XP\WIN7\WIN8\8.1\10\IOS\安卓） Connect to all current OS (XP/WIN7/WIN8/8.1/10/iOS/Android): keyboard works normally | 电脑\平板 PC/Tablet |
